Overview & Features
Fiber Optic Converter 4401.3 for DS Strobes. Converts the electrical bulkhead of any Ikelite DS strobe into a fiber optic port.
Updates
This 3rd Generation of the Fiber Optic Converter features a hard
anodized aluminum plug connection which reduces weight without
sacrificing durability. It is recommended for use with any Ikelite
strobe produced September 2018 or later with a hard anodized aluminum
bulkhead.
Like the 2nd Generation model, this Fiber Optic Converter features
heightened sensitivity for use with SEA&SEA or Nauticam housings
with internal electrical-to-optical flash triggering devices. These
devices translate the camera's electrical signals into a series of LED
flashes which are much less bright than a traditional built-in camera
flash. The Fiber Optic Converter is also compatible with any system
where the camera's built-in flash can be seen by a fiber optic cord.
Attachment and Use
The Converter simply attaches to the strobe's electrical
bulkhead in place of a sync cord connector. The enlarged slave window
provides approximately 90 degrees field of view for remote triggering.
The Fiber Optic Converter automatically configures itself for
compatibility with both pre-flash and non pre-flash camera modes. No
setting of small switches or confusion over number of pre-flashes.
Simply turn on your strobe and take one picture to configure. This
adapter is a manual exposure (non-TTL) trigger only. The strobe's
output may be adjusted using the manual power settings built into the
strobe (varies by model).
An individual Fiber Optic Converter and compatible cord is needed for
each strobe. Use of two strobes requires two Fiber Optic Converters.
This converter attaches to an Ikelite DS strobe. It is not intended
to be attached to a housing and will provide no functionality if
attached to an Ikelite bulkhead in a housing.
Alternatives
There are two shooting scenarios where the High Sensitivity Optical Slave Converter # 4405 would be a better option:
- If you're shooting a DSLR or mirrorless camera with Nauticam fiber
optic converter and want to shoot at a higher frame rate (4 FPS or
faster).
- If your primary purpose is to trigger your strobes remotely at a
distance from the housing without a fiber optic cable in between.
Strobe Compatibility
- Ikelite DS50, DS51
- Ikelite DS125
- Ikelite DS160, DS161
Technical Specifications
- 1.1 diameter x 2.7 in (28 x 69 mm)
- Weighs 1.6 oz (45 g)
- Depth rating 300 ft (90 m)
What´s Included
- Fiber Optic Converter
- Connector protector # 0301.12
Warranty
IKELITE provides a limited warranty to
the original purchaser against all defects in original workmanship and
material under normal SCUBA use and service as outlined in the owner's
manual for
2 years from the date of purchase, with the following exceptions:
- This warranty does not cover commercial or rental use.
- Should your equipment prove to be
defective for any reason (other than those listed in the limitations
section below) it will be repaired or replaced at IKELITE´s discretion, free of charge, excluding shipping and
handling charges.
- Repairs made under this warranty will not extend the warranty period
- This warranty is non-transferable and applies to the original purchaser only.
- All correspondence concerning this warranty must be accompanied by a copy of the original sales receipt.
- Any flood or damage, for any reason,
that is caused from flooding an O-ring sealed or water tight area will
not be covered under warranty. All O-ring sealed products undergo
extensive factory pressure testing before being shipped and delivered
and are therefore guaranteed to be sealed and functioning when shipped
from the factory.
- IKELITE nor ADITECH will not be liable for any
loss, damages, or expenses including incidental or consequential damages
directly or indirectly arising from the sale or use of the product.
- IKELITE accepts no liability for any loss of captured images or the
inability to capture images even if it is due to the malfunctioning or
leakage of the housing.
- All paint finishing, cosmetic
discoloration of surfaces, powder coating, or material stitching that is
chipped, damaged, or unthreaded through customer use is not covered in
the warranty.
- IKELITE does not warranty any product
for aesthetic finishes. Issues with surface finish that do not affect
function of the product are not covered under warranty.
- This warranty does not apply and may
be rendered completely void in the event of accidental damage, abuse,
overcharging of battery, flooding due to neglect, tampering, lack of
care and maintenance, improper storage, or unauthorized service.
- This warranty specifically excludes lenses, cords, connectors, O-rings, or other conditions
resulting from misuse and negligence.
- This warranty becomes void if the housing components are damaged by anything other than normal recreational diving use.
- Modifications or repair by anyone other than an authorized IKELITE Dealer or ADITECH Service Department will void the warranty.
- By purchasing this product you agree
and understand that in no event will IKELITE, its distributors or
retailers, be held liable for any personal injuries resulting from its
operation, or any other damage whether direct, indirect, incidental or
consequential, even if IKELITE or ADITECH is advised of such damages.