Customer Support
(254) 654-0522

Mangrove Snoot SNLC-Z330 (Inon Z-330/D-200)

Manufacturer: MANGROVE UW
Availability: Usually ships in 2-3 business days
The Mangrove Snoot Set with centred laser pointer is an accessory for the INON Strobes Z-300, D-200 to change the beam angle.

Price $170.00

Shipping cost from $28.00
Calculate shipping cost

Add to Cart

The Mangrove Snoot Set with centred laser pointer is an accessory for the INON Strobes Z-300, D-200 to change the beam angle. The various combinations of packaged parts deliver 7 different beam angles of coverage with the following sophisticated effects:

  • To block extra diffused light eliminating backscatter
  • To highlight a subject by illuminating the subject only
  • To give a spotlight effect on a subject



  • The snoot size is adjustable via a series of screw-on nozzle segments.
  • Getting snooted shots is much easier to accomplish with the help of the centred laser pointer.
  • This aluminium snoot fits tightly to the front of the strobe and has 7 sizes of openings.
  • Used to shape the light to smaller amounts and direct it on or near the subject, snoots are very popular, as they eliminate background lighting and backscatter behind the subject.
  • Many creative effects can be achieved by lighting part of the subject, or using back lighting as well. However, up until now, they have been very hard to aim correctly.
  • The red laser pointer helps target your snoot. Instead of relying on guessing where your small snoot beam of light is pointed, a laser shows the user the exact target.
  • Additionally, the laser is programed to shut off whenever a strobe is fired, so the red aiming light does not show in the picture
  • The laser light has a push button on-off switch and is powered by three small long lasting LR44 batteries.
  • There are 7 opening rings that screw off, and also a neutral density filter.
  • A snap cord is included so that you can secure it to the strobe when not in use.

Tested Pressure

  • Laser Housings Individually Tested to 10 Bar (90 m / 300 ft.)
  • Recommended Working Pressure : 60 m

Closure Design

  • O-ring

Body Material

  • Marine Grade Aluminium

Overall Size (Length x Diameter)

  • 209 x 168 mm for Inon Z240 209 x 78.5 mm for Inon S2000
  • 209 x 79 mm for Sea&Sea YS-110 209 x 92 mm for Ultra Max

Total Weight

  • Approx. 0.30kg for Inon Z240 Approx. 0.28kg for Inon S2000
  • Approx. 0.28kg for Sea&Sea YS-110
  • Approx. 0.30kg for Ultra Max
  • Buoyancy (with Flash)
  • Slightly Negative in Salt Water

Laser Pointer Power Source

  • 3 x LR44 Button Cell (not included)
Aditech provides a limited warranty to the original purchaser against all defects in original workmanship and material under normal SCUBA use and service as outlined in the owner's manual for 2 years from the date of purchase, with the following exceptions:
  • Should your equipment prove to be defective for any reason (other than those listed in the limitations section below) it will be repaired or replaced at Advanced Diving Technologies´ discretion, free of charge, excluding shipping and handling charges.
  • Repairs made under this warranty will not extend the warranty period
  • This warranty is non-transferable and applies to the original purchaser only.
  • All correspondence concerning this warranty must be accompanied by a copy of the original sales receipt.
  • Any flood or damage, for any reason, that is caused from flooding an O-ring sealed or water tight area will not be covered under warranty. All O-ring sealed products undergo extensive factory pressure testing before being shipped and delivered and are therefore guaranteed to be sealed and functioning when shipped from the factory.
  • All batteries and chargers are warranted by the original battery/charger manufacturer.
  • Lithium Ion battery packs are warranted for 6 months.
  • Aditech will not be liable for any loss, damages, or expenses including incidental or consequential damages directly or indirectly arising from the sale or use of the product.
  • ADITECH accepts no liability for any loss of captured images or the inability to capture images even if it is due to the malfunctioning or leakage of the housing.
  • All paint finishing, cosmetic discoloration of surfaces, powder coating, or material stitching that is chipped, damaged, or unthreaded through customer use is not covered in the warranty.
  • Aditech does not warranty any product for aesthetic finishes. Issues with surface finish that do not affect function of the product are not covered under warranty.
  • This warranty does not apply and may be rendered completely void in the event of accidental damage, abuse, overcharging of battery, flooding due to neglect, tampering, lack of care and maintenance, improper storage, or unauthorized service.
  • This warranty specifically excludes bulbs, lenses, cords, wet connectors, O-rings, fuses or other conditions resulting from misuse and negligence.
  • This warranty becomes void if the Video Housing components are damaged by anything other than normal recreational diving use.
  • Modifications or repair by anyone other than an authorized ADITECH Dealer or ADITECH Service Department will void the warranty.
  • By purchasing this product you agree and understand that in no event will ADITECH, its distributors or retailers, be held liable for any personal injuries resulting from its operation, or any other damage whether direct, indirect, incidental or consequential, even if ADITECH is advised of such damages.