Overview & Features
A full featured and durable waterproof housing for Canon
EOS 5D Mark III, 5D Mark IV, 5DS, and 5DS R DSLR cameras. Suitable for
scuba, snorkel, surf, pool, and any application in or around the water.
Key Features
- 200' (60m) depth rating
- Housing back is interchangeable with optional lightweight 50' (15m)
back (sold separately); the 50' back is lighter weight for travel and
perfect for snorkeling, surf, and pool work
- Perfect for any wet environment including surf, dive, and pool use
- Supremely functional for maximum creative control—access is provided for all important camera functions
- The new Dry Lock (DL) Port System gives added security at the surface of the water and accommodates large diameter lenses
- Extra-large, soft touch zoom knob; Zoom is accessible for many lenses using our unique universal zoom gear system
- Vacuum valve included; Test your system after assembly prior to entering the water; Pump sold separately
- Included Ikelite ICS-5 bulkhead connector with manual hotshoe for
reliable electrical triggering of underwater strobes; Optional TTL
circuitry provides automatic exposure with compatible Ikelite DS strobes
- Control symbols are laser etched into the back and will never fade or rub off
- Quick install camera mount plate does not need to be removed for battery or memory card access
- One spare 1/4-20 threaded accessory port locations on the front of the housing for the addition of optional accessories
- Includes a balanced aluminum base with left-hand quick release handle; Right-hand handle sold separately
- Signature open-groove design suspends the rear o-ring in a natural
position that is easier to maintain and more reliable than forcing the
o-ring into a channel
- ABS-PC and Lexan construction is fundamentally corrosion-resistant
- Made in the USA; Individually inspected for fit and water pressure tested to depth
- 1 year limited warranty
TTL Exposure
Install optional CT1K Canon TTL Kit # 46070 for automatic TTL
exposure with compatible Ikelite DS-model Strobes. Ikelite DS-model
strobes may be used with this system without the Canon TTL Kit
installed, but will not provide TTL exposure.
Non-Ikelite Strobes
SEA&SEA, INON, and Nikonos strobes with an electrical connection
can be triggered in manual exposure modes using an electrical sync cord.
Strobes without an electrical sync cord connection cannot be attached
to this system unless slaved off of a hard-wired strobe.
Ikelite Non-Digital Strobes
Older non-digital strobes featuring an ICS-5 electrical sync cord
bulkhead can be used with this system in manual exposure modes.
Fiber Optic
Fiber optic only strobes are not compatible with this installation.
An external strobe must be connected by electrical sync cord.
Remote Triggering
Strobes with remote slave capabilities may be triggered off of a
flash attached to the housing by electrical sync cord. Ikelite DS
strobes support remote triggering using the Optical Slave Converter
Product number 4403 or the Water Wizard system (manufactured and sold by
Aquatica).
Compatibility
This housing is only compatible with cameras as shipped by the
manufacturer. Unless otherwise noted, this housing does not accommodate
the use of add-on grips, battery grips, eyepieces, LCD covers, or other
accessories.
Differences in lens and control placement prevent other DSLR models
from being used in this housing. We are not aware of any other models
which may be used in or adapted to this particular housing.
Technical Specifications
- 200' (60m) depth rating
- Compatible with DL system lens ports
- 1/4-20 thread base mounts with 3.5" spacing
- Near neutral buoyancy in fresh water
- Actual buoyancy varies depending on choice of lens and port
- 5.1 lb (2.3 kg)
- 9.2 x 7.1 x 6.5" (234 x 180 x 165 mm)
What´s Included
- Housing
- Rear O-ring # 0132.61
- Front O-ring # 0132.45
- Base with Left-Hand Quick Release Handle # 4077.67
- Port Hole Cover # 0200.92
- Zoom Gear Retainer # 75900
- Waterproof Bulkhead Cap # 9104.5
- Silicone Lubricant # 0184.2
- Control + Pushbutton Tip Assortment # 9249
- 1/16" Hex Key # 0945.16
- 1/8" Hex Key # 0945.18
- 1 year limited warranty
Not Included:
- Camera Body
- Lens
- Lens Port
Warranty
IKELITE provides a limited warranty to
the original purchaser against all defects in original workmanship and
material under normal SCUBA use and service as outlined in the owner's
manual for
1 year from the date of purchase, with the following exceptions:
- This warranty does not cover commercial or rental use.
- Should your equipment prove to be
defective for any reason (other than those listed in the limitations
section below) it will be repaired or replaced at IKELITE´s discretion, free of charge, excluding shipping and
handling charges.
- Repairs made under this warranty will not extend the warranty period
- This warranty is non-transferable and applies to the original purchaser only.
- All correspondence concerning this warranty must be accompanied by a copy of the original sales receipt.
- Any flood or damage, for any reason,
that is caused from flooding an O-ring sealed or water tight area will
not be covered under warranty. All O-ring sealed products undergo
extensive factory pressure testing before being shipped and delivered
and are therefore guaranteed to be sealed and functioning when shipped
from the factory.
- IKELITE nor ADITECH will not be liable for any
loss, damages, or expenses including incidental or consequential damages
directly or indirectly arising from the sale or use of the product.
- IKELITE accepts no liability for any loss of captured images or the
inability to capture images even if it is due to the malfunctioning or
leakage of the housing.
- All paint finishing, cosmetic
discoloration of surfaces, powder coating, or material stitching that is
chipped, damaged, or unthreaded through customer use is not covered in
the warranty.
- IKELITE does not warranty any product
for aesthetic finishes. Issues with surface finish that do not affect
function of the product are not covered under warranty.
- This warranty does not apply and may
be rendered completely void in the event of accidental damage, abuse,
overcharging of battery, flooding due to neglect, tampering, lack of
care and maintenance, improper storage, or unauthorized service.
- This warranty specifically excludes lenses, cords, connectors, O-rings, or other conditions
resulting from misuse and negligence.
- This warranty becomes void if the housing components are damaged by anything other than normal recreational diving use.
- Modifications or repair by anyone other than an authorized IKELITE Dealer or ADITECH Service Department will void the warranty.
- By purchasing this product you agree
and understand that in no event will Nauticam, its distributors or
retailers, be held liable for any personal injuries resulting from its
operation, or any other damage whether direct, indirect, incidental or
consequential, even if IKELITE or ADITECH is advised of such damages.